Indoor slippers "Comfort" with felt soles
You will need:
A pair of felt insoles of the required size (we have 38);
Awl;
Yarn - 100g / 300m, wool mixture;
Hooks - No. 3 and No. 2;
Needle.

At the first stage, you need - insoles, an awl and hook No. 2. The insoles need to be tied with single crochets (st. b.n.). To do this, we pierce holes in the insole with an awl, retreating 5 mm from the edge. The distance between the holes should also be 5 mm. To avoid tightening the edge and uniformity of the strapping, perform 1 air loop (vp) between the posts.
Tip: In order not to lose the holes, due to the peculiarities of the structure of the felt, it is better to tie at the same time as making the holes. That is, pierce and then do st.b.s.

For greater aesthetics of the product and a light massage effect, as well as so that the feet are not too hot from the felt sole, we will make a duplicate insole. It repeats the shape of the insole and is performed as follows:
For 38 leg sizes, we collect a pigtail from 38 ch. already with the main hook No. 3 and knit in a spiral:
1st p. - from Art. b. n, knitting 3 columns in the first and last loop.
2 p. - again Art. b. n., but 3 end columns turn into 6, thanks to increases.
3 p. - shaping the insole. The narrow part is knitted. b. n., in the place of its expansion 2 half-columns with a crochet, and wide - with columns with 1 crochet. We continue to make additions.
4 p. performed by analogy with 3 p. The only difference is that now 2 p / st with n. shifted 2 loops closer to the narrow part of the insole, relative to 3 p.
5 and subsequent rows - We knit st.b.n. along the contour of the sample. Constantly applying the sample to the insole, the moment of knitting completion is determined.
Tip: It is better to make a knitted sample 3-5 mm less than a felt one along the contour. Sewn a little "tight" it will not puff. In addition, the felt insole will "sit down" a bit when worn.
We sew a knitted insole to a felt insole with a large needle with frequent stitches “over the edge”.

This is how the completely finished slipper sole looks on the reverse side:

For the upper part of the slipper, we collect 5 ch. We turn over when moving to each new row, performing 1 ch. rise before knitting a new row.
1. Double the number of loops by knitting 2 tbsp. b. n. from one loop.
2. We knit without changes 10 tbsp. b. n.
3. Double (= 20 loops).
4. No change Art. 20 b. n.
5. An increase at the beginning and at the end, as well as on the central 2 tbsp. b. n. (= 24 p.).
6. 24 st. b. n.
7. Increases (28 st. b. N.).
8. 28 Art. b. n.
At this point, the end of the additions can be marked by tying a colored thread, or by putting on a marker or pin. Next, we knit on 28 loops of st.b.n. in straight and reverse rows before the start of lifting the foot - 11 "stripes" of the canvas.
It turned out the top of the slipper - "shell":

For a more comfortable fit and secure fastening of the top of the slipper to the sole, we perform "sides". At the extreme 8 st.b.n. , starting from the edge, we perform a gradual decrease in the number of columns. Decreases are made through the row, only along the front side of the sample on one side, starting from the 2nd row, until 1 loop remains, which we close and break the thread. Do the same on the other side.

This is what the resulting sample looks like, folded in half:

We sew it to the sole, marking the middle points and aligning them. It is more convenient to sew in two stages - separately from the middle to the sides.

We tie the finished slippers with small hook No. 2, alternating Art. b. n. and "shells" from Art. double crochet with pico.

Knitted slippers with felt soles: photo and work technique

Knitted products are striking in their diversity. In addition to fashionable and very original models, small items for household use are also very popular. How nice it is to wear soft warm knitted slippers that are made by hand.
Color, design, shape - everything can be chosen according to your taste and possibilities. It is very easy and quick to knit slippers on felt soles with knitting needles. There are several ways that needlewomen willingly use. Some of them are within the power of even those who first picked up the knitting needles. To work, you need to prepare some materials. Buy accessories in the store. It can be buttons, buckles, fasteners and anything that seems extraordinary to you.

Photo master class with a description of the progress of work

When knitting you will need:

• yarn;
• knitting needles;
• felt soles or insoles (bigger size is better);
• hook;
• dense thread;
• thick needle.

Another important addition for beginners will be a video or a master class with step-by-step photos.
To make the slippers soft, warm and pleasant for the legs, you need to choose the appropriate yarn. It is good if it is pure wool or with the addition of acrylic. The thickness and color of the thread is chosen at will. Thin yarn can be used in two additions. Then the slippers will be warmer. Craftswomen often make small knitted items from the remnants of yarn, they also dissolve out-of-fashion or old models.


Knitting needles are selected according to the thickness of the thread. The diameter can be taken a little more, then the knitting will be more voluminous.
To knit slippers with felt soles, of course, you need to prepare the sole itself. A felt insole or a felt blank cut with your own hand will do. Before starting work, we choose a method for making slippers. Can:

• crochet the sole, piercing the felt. In this case, one row of columns must be laid around the entire perimeter of the insole, sticking a hook into the sole. Then knitting loops from the pigtail are knitted and knitting is continued;
• sew with a strong thread with an overcast seam. With such a seam, a chain of threads is also formed. Therefore, dialing the first row with knitting needles will not be difficult;
• knit the detail of the slippers separately and then sew to the felt sole. This is the easiest way.

Option one It is necessary to prepare the sole according to the size of the foot. Immediately take the thread, which is intended for knitting. But, the first row is crocheted.

The strapping is done so that the punctures are distributed at an equal distance. This will provide a neat look to the slippers. If this method has to be applied for the first time, then the video for beginners will help you deal with it very quickly. Then a knitting needle is inserted into each loop of the resulting chain and the loop is pulled through, so the first row is dialed. Then knitting is continued with the chosen pattern, but three central loops are knitted together on the toe of the slippers. This must be done in every row. At the same time, they make sure that the middle loop does not move, forming an even, neat chain. Having tied up to the desired height, the loops are closed. If the knitted slippers are a little wide, you can thread the braid along the top edge and decorate in front of the bow.

Option two Option 2. For this method, you need a thick needle with a large eye and a strong thread. The sole along the entire perimeter will have to be neatly sheathed with an overcast seam. The distance between the needle holes and the stitch height must be the same, otherwise the work will look sloppy. It helps a lot to watch a video with training material on sewing. Then they pick up loops with knitting needles from a pigtail and continue to knit identically to the first option.
The third option for slippers Option 3. The easiest way to quickly knit slippers, even without experience with knitting needles. In this case, they collect such a number of loops that will provide the desired height. It is better to calculate the number of loops for the set. They continue to knit the fabric in the form of a scarf in the usual garter or stocking stitch.

If you need to make knitted slippers in a gift version, then experiment with choosing a pattern. The length of the "scarf" is 30 cm for size 36. The loops are closed in one row and the fabric is sewn to the sole. In this case, you need to try not to make creases or folds.

The seam is laid, stepping back from the edge of the sole 0.7 cm. This will increase the life of the slipper. We make a small overlap on the toe.

Slippers can be decorated in any acceptable way. A master class on making jewelry with your own hands will tell you the most suitable choice.

Video: Knitting slippers on knitting needles

A selection of photos of MK

Comments

related posts:

Knitted house slippers on two knitting needles with a description and a video tutorial
How to knit Japanese slippers with knitting needles according to a photo and video lesson

Crocheted slippers are best done on the sole or insole. The insole can be felt, leather, fur. You can cut the soles from the tops of old boots.

Home slippers are crocheted from separate 6-coal motifs. It is advisable to take the insole one size larger. If it is uncomfortable with a simple insole, buy an orthopedic one.

For work you will need:

1. Cotton yarn type "Violet" - 150 grams.
2. Hook 3 mm.
3. Insoles.
4. Scissors.
5. Awl or thick needle.

The yarn must be connected in two threads, and if the yarn is thin - in three. The knitting should be tight so that the slippers keep their shape and are comfortable. First, we tie the insoles, which we first pierce with an awl, departing from the edge of 0.5 cm. The distance between the holes is 0.5 cm.

When tying, we use single crochets, two in each hole. Then you need to measure the length of the tied insole around the perimeter in order to further calculate the length of the motif.

A prerequisite is that the length of the side of the motif, multiplied by 8, must be equal to the length of the insole around the perimeter (if necessary, you can change the pattern by removing or adding rows in it).

Collecting slippers. To do this, we take three ready-made motifs and sew them according to the following scheme: we sew the sides marked with the number 1 with one front seam. We sew the sides marked with the number 2, getting the back seam. The sides under the number 3 will be sewn to the insole in the future. The sides marked with the number 4 are left unsewn.

You can crochet motifs from the outside, or use a needle and sew them from the inside - whichever is more convenient for you.

It should work like this:

Chop off the details together with the insole with pins or bast by moving the spout to the right or left of the central part. This will turn out the right and left slippers. We tie our slippers to the insole. We got comfortable slippers.

For these colorful slippers, it is better to take a felt sole. Optionally, it can be replaced with cut out leatherette or fur.

For work you will need:

1. Yarn-wool or wool with acrylic - 150 grams.
2. Hook 3.5 mm.
3. Felt insoles.

We start knitting with a sock. The pattern can be anything, the main thing is that it is convenient for adding. We knit with a pattern of double crochets. We make additions to the little finger, that is, 4-5 cm.

At the level of the rise, we pass to the sidewalls and begin to knit in this way.

This is how the canvas turns out. It looks like the letter P. The length is determined by applying to the foot or insole.

Here is a knitting pattern for the beginning of a sneaker.

Sew the back seam. We do this without breaking the thread, from bottom to top with single crochets.

We continue to knit in a circle. The height of the slipper depends on your desire.

We attach the top to the sole, fasten it with pins, so that it is more convenient to sew on.

Sew the top to the sole with a seam "over the edge". It is better to take a stronger thread.

These comfortable warm slippers suitable for both children and adults. This model has a knitted and leather sole. To work, you need wool yarn (you can have leftovers) and a small hook. The scheme is given for 37-38 foot size. If you need a different size - add or decrease the number of air loops. We collect 22 air loops and knit a trace according to the scheme:

For one slipper, we need two knitted footprints. Below is a trail for children's slippers, for them to dial 18 air loops (given for comparison).

To begin with, we take one trace and begin to knit slippers from a series of concave relief columns.

Here's what should happen.

View from the back.

We begin to make reductions from the third row.

We do the reductions as follows: 3rd, 4th, 6th and 8th rows - decreases on the central five columns. We knit the 1st, 3rd and 5th convex columns together, as unfinished, skip the 2nd and 4th.

5th and 7th rows - on the central nine columns we make decreases, knitting the 1st, 3rd, 5th, 7th and 9th convex columns together, like unfinished columns. 2nd, 4th, 6th and 8th skip.

We knit the second slipper, like the first.

From a piece of leather we cut out the sole, a little less than a trace. We sew the sole on the machine. If you don't have a machine, you can do it manually.

We attach the blank to the slipper and sew.

Is it possible home comfort without comfortable and cute slippers? It is this attribute that helps to relax and understand that you are finally at home.
Today, the assortment of home shoes on store shelves is quite rich. But it’s much more pleasant to dress your tired legs in your own slippers after work.

Making your own shoes for the house is not at all difficult. Surely, in your home there is a piece of leather, substitute, dense fabric, fur. And accessories for slippers can be bought in handicraft stores or decorated independently to your taste. Some craftswomen enthusiastically knit slippers with a crochet or knitting needles, decorating products with various inscriptions, bows, drawings.
After viewing this master class, you will be able to knit slippers from yarn. It's easy and simple. Soft, warm, light handmade slippers give not only comfort and warmth, they envelop the craftswoman with care and delight the eye for a long time.

Material for making slippers:

1 skein of yarn (100 grams, 220-240 meters);
knitting needles 3-3.5 mm in size;
2 insoles;
medium sized needle;
strong nylon thread.

Stages of work

1. When choosing yarn for a future product, it is advisable to give preference to 100% wool or wool with the addition of acrylic. In this case, the slippers will turn out to be very warm, and will last for more than one year. If you use a thinner thread, you can knit in two threads. In this case, the product will turn out to be very durable and wearable.
We will make slippers for a graceful female leg of size 36. To begin with, we collect 16 loops on the knitting needles. It is necessary to type on two knitting needles at the same time, so that later it will be easier to knit.

2. The loops are dialed, we begin to knit an ordinary long fabric with knit and purl in the form of a scarf.

3. We move gradually row by row. We end up with a nice rectangular piece.

4. The piece to be made should be about 30 centimeters long.

5. Now you need to sew two parts together: the resulting fabric and the insole.
The material from which the insoles are made can be very diverse, and is chosen to taste. It all depends on the room in which the slippers will be used. If the floor is cold, you need to pick up durable, multi-layer insoles. Their size is selected depending on the size of the foot. It is advisable to take the insole one size larger. In this case, slippers will be more spacious.
It is most convenient to start stitching from the front of the slipper, from the toe, and go in a circle counterclockwise.

6. From the edge of the insole, you need to make a small indent, approximately 0.7 mm. If you make the edge smaller, slippers will soon become worthless.

7. Gradually moving in a circle of the product, carefully lay a line at the same distance from the edge.

8. At the turn, in the heel area, we try not to make folds. When sewing, carefully straighten the fabric.

9. We complete the stitching in the place from which we started, while making a small overlap. You can go around the insole with a needle and thread twice. This will guarantee the durability of the product.

Slippers on the sole are ready!

If desired, the product can be decorated with a bow, buttons, and other interesting details.
Such cute slippers will appeal to everyone in the winter cold. They will not only be able to warm you, but also give good mood. In addition, they can become nice gift close person, because they are made by hand with the best wishes.

Warm cozy slippers - socks are knitted on the basis of felt soles. To knit such slippers, you need to purchase footprints made of felt or other material.

For knitting slippers you will need yarn 100 gr Alize Lana Gold classic, stocking needles No. 4.5, hook No. 4.5, additional knitting needle, gypsy needle.

The slipper consists of two parts - a knitted felt sole and an upper part knitted.

First, you need to overcast the felt sole, then a strapping is made on the basis of the seam. Take a strong cotton thread, thread it into a gypsy needle, making a puncture 5 mm from the edge, perform overcasting stitches.

Having swept the sole in a circle, proceed to tying it. To do this, take a hook, yarn, make an initial loop on the hook. Insert the hook into the overcasting thread and make a connecting column and 1 air p. Next, knit a row of st.b / n, introducing a hook for overcasting stitches. To complete the initial row, perform the connection. from the 1st lifting loop.

To go to the next row, make 2 air stitches, knit a row of embossed columns with one crochet, inserting a hook into the legs of the columns of the initial row at work, a relief pigtail of loops will form along the edge, and the direction of the columns will be perpendicular to the sole - this is the beginning of the side part . Finish a number of connections. into the second lifting loop and the lower part of the slipper is ready.

Knitting the upper part of the slipper begins like knitting a sock, with a cuff. Type 11 loops on four stocking needles, lock them into a ring and knit circular rows with an elastic band 1x1. In the 1st row, alternate the front and back loops, and in the next rows, follow the pattern of the elastic band according to the drawing, make front loops over the front loops, and purl loops over the wrong ones.

Having connected the cuff of the desired length, proceed to knitting the instep of the foot. To do this, divide the loops in half, on two knitting needles - heel loops and 22 loops on two loops - for the front. Next knit 5 circular rows stockinette stitch, at the same time, make additions on the sides, knitting 2 loops from the last loop of the back part for the front and behind the back wall and after knitting the front loops, make additions on the first loop of the back part, knitting 2 loops from the front and back walls. After 5 rows, 16 loops are formed on the knitting needles of the back part, and the number of loops of the front part should not change, they can be re-shot onto one knitting needle.

Next, knit straight only the front part of the front and back rows.. On the 1st row, work the first crossing of loops to form a braid on the central 12 loops. Perform 1 edge p., 4 front p., remove 4 front p. on an additional knitting needle, place them before work, knit the next 4 loops, then 4 loops from an additional knitting needle and the remaining loops from the left knitting needle.

After 5 rows in the 6th, perform the second crossing of the loops. After knitting 1 edge stitch from the beginning, 8 front stitches, 4 stitches, remove to an additional knitting needle and place it at work, knit the next 4 loops, then loops from the additional knitting needle and the remaining loops from the left knitting needle.

Alternate weave every 6th row. Work the front piece until the toe tapers, then stop shaping the braid and start decreasing at the toe. To do this, in each front row, perform 1 chrome p., 1 p. with a broach to the left, then the front loops along the row until 3 loops remain on the left knitting needle, knit 2 together with the front and 1 front. When the length of the front is equal to the length of the sole from the heel to the edge of the toe, cast off the remaining loops.